Contact Us Today

 

 

Everyone will have their own individual theory in relation to Installing A Bathtub.

Setting up a tub isn't specifically brain surgery, yet it does require solid plumbing, woodworking, and also sometimes, tiling skills. Changing an old tub with a brand-new one is also a moderately difficult task. If the old tub is easily obtainable, the project can move rapidly; if you need to open a wall to eliminate the old bathtub as well as place the new bathtub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and also set in the new one. Ensure you have qualified yourself for the task as well as are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Possibilities are you might require an expert plumber to make tube connections.
This short article will aid you mount a brand-new bathtub in your restroom if you have already gotten a brand-new bathtub and also do not require to transform the setup of your previous water supply pipes.
Your tools and material checklist ought to comprise the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Preparing for the Installation

Firstly, the sustaining framework supplied with the bath should be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent strain on the tub.
Fit the versatile tap connectors to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you use every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its last setting.

 

 

Removing Old Taps

If you require to replace old faucets with new ones as a part of your installation, then the first thing you should do is detach the supply of water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The process of getting rid of the existing taps can be quite bothersome because of the restricted accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing compound.
Before carrying on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.

 

 

Mounting the Bathtub

Utilizing both wooden boards under its feet, put the bath tub in the required placement. The wooden boards are practical in evenly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four tiny factors.
The next objective is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bath tub until the level reads degree.
To install faucets, fit all-time low of the outermost flexible tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the other faucet.
Activate the water supply as well as examine all joints and also new pipework for leaks as well as tighten them if essential. Fill the tub as well as additionally examine the overflow outlet as well as the typical electrical outlet for leakages.
Finally, repair the bath paneling as explained in the supplier's instruction manual. Tiling and sealing around the tub must wait till the bath tub has been used a minimum of once as this will resolve it right into its last placement.

 

 

Suitable New Touches

If the tails of the new taps are plastic, then you will need a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin making sure that the washers are in place between the tap as well as the sink. Protect the faucet in position with the supplier provided backnut. Once the tap is securely in place, the supply pipes can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The former type needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.

 

 

Tiling Around the Tub

In the area where the bath satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall between the bath and also the tiling, causing problems with dampness and feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, and also can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub remains in usage. The sealant can crack rather very early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or waterproof glue as well as cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

Do you really like more info about How to Install a Bathtub Yourself? Make feedback further down. We'd be interested to listen to your views about this write-up. In hopes to see you back again before long. Do you know about someone else who is enthusiastic about Tools You Need to Install a New Bathtub ? Do not hesitate to share it. I take joy in reading our article about How to Install a Bathtub.

Find Out More